Electric Motors

Product Details:

IN THIS GEAR MOTOR HAS LOTS OF AMAZING FEATURE VOLTAGE RANGE OF THIS MOTOR IS 6V-24V RPM IS BASED ON CURRENT VOLTAGE IF WE GIVES 6V IT GIVES 5 RPM ON 12V THERE IS 10 RPM AND 24V 20 RPM .IT IS EXPLOSION FREE PRODUCT.LOAD CURRENT: 0.2A-0.24A BEST FOR DIY AND SMART CAR AND INDUSTRIAL PURPOSE.

Additional Information:

• Production Capacity: 500
• Delivery Time: 1 DAY

Product Details:

Micro DC 3-6V Micro Submersible Pump Mini water pump For Fountain Garden Mini water circulation System DIY project. This is a low cost, small size Submersible Pump Motor which can be operated from a 3 ~ 6V power supply. It can take up to 120 liters per hour with very low current consumption of 220mA. Just connect tube pipe to the motor outlet, submerge it in water and power it. Make sure that the water level is always higher than the motor. Dry run may damage the motor due to heating and it will also produce noise.
 
Specifications:-
 

Operating Voltage : 3 ~ 6V

Operating Current : 130 ~ 220mA

Flow Rate : 80 ~ 120 L/H

Maximum Lift : 40 ~ 110 mm

Continuous Working Life : 500 hours

Driving Mode : DC, Magnetic Driving

Material : Engineering Plastic

Outlet Outside Diameter : 7.5 mm

Outlet Inside Diameter : 5 mm

Additional Information:

• Production Capacity: India
• Delivery Time: 3 days

Product Details:

Our presented series of DC Gear Motor is enormously demanded in the market for their long-lasting nature and superior finish.

Product Details:

Our firm is ranked amongst the reputed names in the market for offering an extensive range of DC Toy Motor. Besides, we present this series to our clients at nominal prices.

Product Details:

The motor wire is made of pure copper enameled wire wound through wire technology.The copper wire is evenly arranged,the temperature rise of the motor is lower,and the deformation and noise will not occur during long-term transportation.silicon steel rotor the bearing is made of international silicon steel material and imported German technology the surface is coated with imported rotor glue to prevent oxidation of silicon steel and reduce the surface burr after grinding.compared with the motor in the same line,the output is more stable the noise is lower and the service life is longer.Package Include 1 x Nema 17 Stepper Motor. Voltage: 3-6 V Torque: 4 Kg-cm Step Angle: 1. 8 deg/step Shaft Diameter: 5mm; Shaft Length: 10mm

Additional Information:

• Production Capacity: 3000
• Delivery Time: 2 days
• Packaging Details: safe packaging with thermocol and bubble wrap

Product Details:

The motor wire is made of pure copper enameled wire wound through wire technology.The copper wire is evenly arranged,the temperature rise of the motor is lower,and the deformation and noise will not occur during long-term transportation.silicon steel rotor the bearing is made of international silicon steel material and imported German technology the surface is coated with imported rotor glue to prevent oxidation of silicon steel and reduce the surface burr after grinding.compared with the motor in the same line,the output is more stable the noise is lower and the service life is longer.Package Include 1 x Nema 17 Stepper Motor. Voltage: 3-6 V Torque: 4 Kg-cm Step Angle: 1. 8 deg/step Shaft Diameter: 5mm; Shaft Length: 22mm

Additional Information:

• Production Capacity: 4000
• Delivery Time: 2 days
• Packaging Details: safe packaging with thermocol and bubble wrap

Product Details:

This DC6-12V MINI Aquarium water Pump R365 is the perfect choice for any project that requires water to be moved from one place to another. Possible uses/projects include; a small aquarium pump, automatic plant watering system, making a water feature or music activated dancing water features to name but a few. When pumping a liquid the pump runs very quietly. The pump is also capable of pumping air, though when pumping air the pump is quite noisy in comparison. The R365 requires between 6 – 12V DC and between 0.5 – 0.7A and will deliver its maximum operating values when power is at the upper end of these ranges. The pump can handle pumping heated liquids up to a temperature of 80°C and when suitably powered can suck water through the tube from up to 2m and pump water vertically for up to 3m. This immersible pump can be used to water your plants, make a fountain or waterfall, and even change your fish tank water. It works quietly with the sound level under 30db. The pump has a filter inside as well as a suction cup which can help stick it to smooth surfaces tightly.

This N20 12V 600 Rpm Micro Metal Gear Motor has small volume, torsion big, all metal gear, durable, not easy to wear. Great replacement for the rusty or damaged DC geared speed reduce motor on the machine. Widely used on Boat, Car, Electric Bicycle, Fan, Home Appliance.

The N20 Micro Gear 12V 600 RPM DC Motor (High Torque) is lightweight, high torque, and low RPM motor. It is equipped with gearbox assembly so as to increase the torque of the motor. It has a cross-section of 1012mm, and the D-shaped gearbox output shaft is 9mm long and 3mm in diameter. It has a very small size so as fit in complex spaces of small-scale application. One can connect this Micro Gear Motor to wheels to drive them from one place to other while carrying high loads.

This N20 Micro Gear 600RPM 12 V DC Motor (High Torque) has small volume, torsion big, all metal gear, durable, not easy to wear. Great replacement for the rusty or damaged DC geared speed reduce motor on the machine. Widely used on Boat, Car, Electric Bicycle, Fan, Home Appliance.

Additional Information:

• Minimum Order Quantity: 500 Piece
• Delivery Time: 1-2 DAYS

Product Details:

M15n-3 Series 6.0 V~28.0V Micro Dc Motor with Gear and Double Shaft Used for Scanner, Dynamo.

Product Details:

This unit uses the latest technology from Ublox to give the best possible positioning information and includes a larger built-in 25 x 25mm active GPS antenna with a UART TTL socket. A battery is also included so that you can obtain a GPS lock faster. This is an updated GPS module that can be used with ardupilot mega v2. This GPS module gives the best possible position information, allowing for better performance with your Ardupilot or other Multirotor control platform.
The Ublox GPS module has serial TTL output, it has four pins: TX, RX, VCC, and GND. You can download the u-centre software for configuring the GPS and changing the settings and much more. It is really good software (see link below).

Product Details:

Stepper motors are used in motion systems high precision positioning is required. Stepper motors can deliver direct and precise motions in a small volume due to their high power even at low speeds, stall torque, and ability to divide steps into micro-steps.
Permanent magnet and hybrid technologies are used to provide a full range of solutions.
The absence of mechanical commutation gives these motors a longer life which is usually given by the sleeves according to the load applied on the shaft.

SPECIFICATIONS

Additional Information:

• Delivery Time: 1 to 2 days

Product Details:

Stepper motors are used in motion systems high precision positioning is required. Stepper motors can deliver direct and precise motions in a small volume due to their high power even at low speeds, stall torque, and ability to divide steps into micro-steps.
Permanent magnet and hybrid technologies provide a full range of solutions.
The absence of mechanical commutation gives these motors a longer life which is usually given by the sleeves according to the load applied on the shaft.

SPECIFICATIONS

Additional Information:

• Delivery Time: 1 to 2 days

Product Details:

Model; Japan MITSUMI / M25N-2G R-14 A265 Voltage; 12V Speed; 160R Voltage; 6V 80R Gearbox including motor; 45MM Gearbox wide; 58MM Gearbox long; 65MM Shaft diameter; 3.5MM Axis length; 7MM Dual flat position; 1.75MM There is a long axis 4.5MM 24V Speed 320Rpm

Product Details:

We are specialized in offering Nema17 Stepper Motor to our customers. Our presented product is extremely used in the market owing to their top features.

Additional Information:

• Production Capacity: 2.8kg

Product Details:

Description: dc 12v solar powered water pump 700l/h brushless magnetic submersible water pump specification: - material: abs(acrylonitrile butadiene styrene) + stainless steel- overall size: approx. 80 x 48 x 63mm/3.15 x 1.89 x 2.48inches
Features: - uses advancedponents and wear-resistant shaft. - smooth operation, high efficiency, good performance, long service life. - can be a long time continuously work, low noise, safety and environmental protection. - widely used in industry, scientific research, aerospace industry

Additional Information:

• Production Capacity: 12051
• Delivery Time: 3days

Product Details:

Stepper motors are used in motion systems high precision positioning is required. Stepper motors can deliver direct and precise motions in a small volume due to their high power even at low speeds, stall torque, and ability to divide steps into micro-steps.

Permanent magnet and hybrid technologies are used to provide a full range of solutions.

The absence of mechanical commutation gives these motors a longer life which is usually given by the sleeves according to the load applied on the shaft.

 

Specifications

Model 60HS65-2804AF Type Bipolar Rated Voltage 3.36V Step Angle 1.8° Rated Current per Phase 2.8A Resistance per Phase 1.2 Ω ±10% Inductance per Phase 4.2 mH ±20% Holding Torque 2.1Nm Rotor Inertia 570gcm² Weight 1.030kg No. of Lead 4 Operating Voltage 24-42V DC Length 65mm Step Angle Accuracy ±3 Arc Minute Protection Class DIN 40050 - IP65

Additional Information:

• Delivery Time: 1 to 2 days

Product Details:

Rated voltage: DC 3V /DC 3.7V /DC 4.5V /DC 6V Rated current: 1000mA / 810mA / 660mA / 500mA Power: 3w /3w /3w /3w Gas nozzle diameter: 5 mm Maximum vacuum degree: - 20KPa (- 150mmhg) Liquid extraction volume: 50-200mlpmNoise: 65db (30cm away)Life test: 100,000 times (No 2 seconds, off 2 seconds)Jet distance: 0.5mSuction distance: 0.5m Weight: 42 g Low fever and low noise -Special motor matching, large voltage regulation range, low heat generation, low noise, small electromagnetic interference, long life and so on. Industrial grade raw materials -It adopts special customized industrial grade raw materials (non-common raw materials) to meet the various severe conditions such as high and low temperature, and is used continuously for a long time.

Product Details:

Technical parameters:

Volt: DC 6v

Current: 200-300mA

Working conditions: 0-40 °

Relative humidity <80%

Flow rate: 20-60 ml / min

Rotate speed: 0.1-60 rpm. Weigh: 150 g

Size: Driver size: Dia.32 x Height 23 (mm) Pump head size: Dia. 54 x Height 46 (mm) Install hole: 47mm

Flow direction: you can control the direction flow of the positive and negative working Silent connection

 

Suitable for aquariums, chemicals, liquids, dosing additives

 

 

Package Include:

1x6v Dc DIY Dosing Peristaltic Pump Dose Head For Aquarium / Chemical Laboratory Water Analysis

The stepper motors move in precisely repeatable steps, hence they are the motors of choice for the machines requiring precise position control. The NEMA17 4.2 kg-cm Stepper Motor can provide 4.2 kg-cm of torque at 1.2A current per phase.

The motor’s position can be commanded to move or hold at one position with the help of Stepper Motor Drivers. The NEMA17 4.2 kg-cm Stepper Motor provides excellent response to starting, stopping, and reversing pulses from the stepper motor driver.

They are very useful in various applications, especially which demands low speed with high precision. Many machines such as 3D Printers, CNC Router and Mills, Camera Platforms, XYZ Plotters etc.

It is a brushless DC motor, so the life of this motor is dependent upon the life of the bearings. The position control is achieved by a simple Open Loop control mechanism so doesn’t require complex electronic control circuitry.

It comes with a detachable 70 cm cable which makes wiring and rewiring very fast and easy work. The design of this cable is such that it can directly be mounted on a stepper motor controller. So, playing with the connection is done with just snap of fingers.

The motor’s shaft has been machined for good grip with a pulley, drive gear etc., and especially avoiding stall or slip

Additional Information:

• Minimum Order Quantity: 200 Piece
• Delivery Time: 1 TO 2 DAYS