Product Details:
Minimum Order Quantity | 100 Piece |
Supportive Speed | 10 Mbps |
Humidity | 98% |
Temperature | 15 Degree C to 25 Degree C |
Module Thickness | 5-10mm |
Add the desired memory to your Arduino project to store the data, Media etc. Micro SD Card Reader Module also called Micro SD Adaptor which is designed for dual I/O voltages. The Module is a simple solution for transferring data to and from a standard SD card. The pinout is directly compatible with Not only with Arduino as shown in the diagram in below, but can also be used with other microcontrollers. Micro SD Card Reader Module has an SPI interface which is compatible with any sd card and it uses 5V or 3.3V power supply which is compatible with Arduino UNO/Mega.SD module has various applications such as data logger, audio, video, graphics.
There are total of six pins (GND, VCC, MISO, MOSI, SCK, CS), GND to ground, VCC is the power supply, MISO, MOSI, SCK is the SPI bus, CS is the chip select signal pin; 3.3V regulator circuit: LDO regulator output 3.3V as level converter chip, Micro SD card supply.
With this Module, general AVR microcontroller system can read the signal
It is a 6 Channel 5V Relay Module with Optocoupler. The relay normally open interface maximum load: AC 250V/10A, DC 30V/10A.With optocoupler isolation, strong drive capability, stable performance; trigger current 5mA, module working voltage: DC 5V.Each channel of the module can be triggered by a jumper to set a high level or a low level. Fault-tolerant design, even if the control line is disconnected, the relay will not move. With status indicator: power (green), 6-channel relay status indicator (red).All module size interfaces can be directly connected through the terminal block, which is convenient and practical.
Additional Information:
Product Details:
Minimum Order Quantity | 100 Piece |
Current | 5.4A |
Material | Copper |
Weight | 15g |
Operating Temp | 25 Degree C |
Board Thickness | 5-10 mm |
Power Bank Module is a super mini power bank mainboard compatible with 3.7V-4.2V li-ion battery. On-board micro USB port for battery charging and USB type A female output port supporting DC 5V 1A input and 5V 1A output. Just connect it with a 18650 battery then you can get a portable power bank.
SpecificationAdditional Information:
Product Details:
Model Number | LM35 |
Linear | + 10-mV |
Accuracy | 0.5% |
Voltage | 4 V to 30 V |
Current | 60A |
We are an accomplished organization which has gained name and fame in providing LM35 Temperature Sensor to the customers.
Product Details:
Minimum Order Quantity | 500 Piece |
Brand | unique india sales |
Model Name/Number | ne555 |
Size | 31mm x 22mm |
Input Signal | >=100 MA |
NE555 Pulse Frequency Duty Cycle Adjustable Module Square Wave Signal Generator is 5V square wave signal generator. It generates a square wave signal used for experimental development. Also, use to drive a stepper motor for generating a square wave drive signal.
The output duty cycle can fine-tune. Duty cycle and frequency is not separately adjustable, adjusting the duty cycle will change the frequency.
Additional Information:
Product Details:
Minimum Order Quantity | 100 Piece |
Model Name/Number | L293D |
Current | 600mA |
Voltage | 5 V to 36 V |
Size | 36 mm x 24 mm |
Material | Copper |
Product Details:
Operating Voltage | 5V |
Model Name/Number | MQ3 |
Operation Temperature | -10 Degree C to 70 Degree C |
Current Consumption | 150mA |
Shape | Rectangle |
Duct description
Features: High quality double panel design, with power indicator and TTL output signal. Have DO switch signal(TTL) output and AO analog signal output. TTL output signal for low level effectively. (When the low output electric signal lights at ordinary times, can be directly connect single chip microcomputer or relay module). Analog output voltage with concentration, the higher concentration, the higher voltage. Has better sensitivity with the liquefied petroleum gas, natural gas, city gas, smoke. Has long service life and reliable stability. Rapid response recovery features. Specifications: Input voltage: DC 5V, power consumption (current): 150 mA, DO output: TTL digital 1 and 0 (0. 1 and 5 V), AO output: 0.1 - 0.3 V (pollution-free). Highest concentration of voltage: Approx. 4V detection range of alcohol: detection range of 10 ~ 1000 PPM. Connection mode: VCC - Positive (5 v), GND - connect power negative, DO - TTL switch signal output, AO - analog signal output.
Product Details:
Minimum Order Quantity | 500 Piece |
Brand | UNIQUE INDIA SALES |
It is 4 Channel Isolated 5V 10A Relay Module, A wide range of microcontrollers such as Arduino, AVR, PIC, ARM and so on can control it.
It is also able to control various appliances and other types of equipment with large current.
Relay output maximum contact is AC250V 10A and DC5V 10A. One can connect a microcontroller with standard interface directly to it.
Red working status indicator lights are conducive to the safe use. It has a wide range of applications such as all MCU control, industrial sector, PLC control, smart home control.
Ready to get switching on your Raspberry Pi?! This neat relay module features 4 x 5V relays rated at 10A/250V each. It is designed to switch up to 4 high current (10A) or high voltage (250V) loads with the help of microcontroller!
Additional Information:
Product Details:
Minimum Order Quantity | 500 Piece |
Model / Part Number | MQ-3 |
Operating Voltage | 5V |
Brand | UNIQUE INDIA SALES |
Warranty | NO WARRANTY |
This is a very easy to use low cost semiconductor Gas sensor Module with analog and digital output. This module uses MQ3 Alcohol gas sensor as a alcohol gas sensing element. It requires no external components just plug in Vcc & ground pins and you are ready to go.
For Digital output the threshold value can be easily set by an on-board potentiometer. Using this module you can easily interface MQ3 Alcohol sensor to any Microcontroller, Arduino or even Raspberry Pi.
Since this Gas Sensor module is sensitive to alcohol it can be used in breathalyser. MQ3 Sensor also has small sensitivity to Benzine.
Additional Information: